Tianjin TAIYITO Technology Co., Ltd 

taiyito

Home > Products > Security/Camera/Audio&Video > Security Product

    TDZLH93(II) ZigBEE Intelligent Smoke Detector

    • No.: TYTVST(IOS) TYTSmart (Android)
    • Brand :
    • Weight:

    TDZLH93(II) ZigBEE Intelligent Smoke DetectorMain Application and Function Control:    With advanced fuzzy control technology, this product can accurately detect the smoldering and burning v

    1. Detailed information

    TDZLH93(II) ZigBEE Intelligent Smoke Detector

    Tianjin TAIYITO Technology Co., Ltd

    Main Application and Function Control:

        With advanced fuzzy control technology, this product can accurately detect the smoldering and burning visible smoke. When the smoke concentration exceeds the set alarm threshold, the detector will begin to alarm until continuously detecting for 20 seconds. Once the smoke alarm has been detected, it will be in the alarming state: TEST indicator light keeps on, and the buzzer rings. When detecting the smoke threshold is below the set alarm threshold, the TEST indicator light will goes out, and the buzzer will still ring. The buzzer will stop to ring when it is disarmed by the APP on the phone.

        It can be used in ZigBEE bi-directional smart home system or independently. When used in ZigBEE bi-directional smart home system, it accepts the wireless ZigBEE 2.4G control signal and can transmit the relevant information signal, which can send the detecting signal directly to the controller(e.g. APP).


    Features:

    Photoelectric detection way

    Ceiling mounted

    Optical maze

    Built-in application-specific integrated circuit

    Special moistureproof design

    Connected to the output mode

    With functions of manual test

    Stable and reliable working performance

    Adopt ultra-thin type structure design

    The metal shield, resistance to high frequency interference


    Technical Parameters:

    Working voltage:DC 12 V;

    quiescent current:≤8mA;

    alarm current:≤35mA;

    operating temperature:-10℃ to +50℃;

    ambient humidity:≤95%RH;

    Alarm output: relay normally open/closed;

    detection sensitivity:Ⅱ、Ⅲ;

    Monitoring area:20㎡;

    S:φ112*41mm


    Product installation:

    Installation: the bottom plate with two screws fixed on the ceiling, then install the rest part on the bottom plate . 

    Wiring:

    Tianjin TAIYITO Technology Co., Ltd

    The netural line connect with the side N of product 

    The live line connect with the side L product 

    The product is not suitable for use in the following locations : Where there is smoke in the normal place; places where larger dust, water mist, vapor, oil mist pollution, corrosive gas; places with relative humidity greater than 95%; places with ventilation speeds greater than 5 m / s


    Product commissioning:

    Tianjin TAIYITO Technology Co., Ltd

    1.Networking

    a)Make sure that the network remote controller is in the networking mode (eg TDWZ6616, refer to TDWZ6616 manual).

    b)Observe the "RESET "button , if the red light flash slowly (about 2 seconds once), the network is successful.

    c)If you find that the red light is flashing, perform 3 (log out network) operation.

    2.Address code learning

    a)Hold " RESET" button (Figure 4) for 6 seconds, until the red light flashes, then enter into the learning state.

    b)Use APP to send a signal (such as security alarm + zone control + smoke detectors + learning), the red light flashes, It means learning success.

    3.Log out networking (Do not do this operation under normal circumstances )

    a)Hold " RESET "button (Figure 4) for 6 seconds, until the red light flashes about release, then enter the learning state.

    b)Press "RESET" button for 12 seconds, until the red light flashes 3 times and release, and then the red light continues to flash, logging out network is successful.





            



    Powered by taiyito  ©2005-2017 www.taiyito.com